Complete solution for solar power EasySolar combines an MPPT solar charge controller, inverter/charger and AC power distribution into a single device. Installation of the device is simple and little wiring is required. AC power distribution The AC distribution consists of a residual current circuit breaker and four AC outputs protected by fuses. One output is controlled by the AC input: it turns on only when AC power is available. PowerAssist function The unique PowerAssist technology prevents overloading of the grid or generator power supply by adding additional power through the inverter whenever necessary. Unique software for solar systems Several software programs (wizards) are available to configure the system for different grid-connected or stand-alone applications. Please refer to http://www.victronenergy.nl/support-and-downloads/software/

BlueSolar Charge Controller MPPT Solar charge controller for 12V and 24V batteries   Ultra fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency Efficient passive cooling without fans. Maximum efficiency over 98%. Utilize maximum charging current up to +40°C (104°F). Internal temperature sensor adjusts constant and charge retention voltages depending on temperature. Flexible charging algorithms Fully programmable charging algorithm (refer to software information), plus eight pre-programmed algorithms selectable via a rotary knob (refer to our manual for more details). Real-time monitoring with accessories Monitoring can be done with the appropriate accessories, either with a "ColorControl panel" or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding operating instructions.

BlueSolar Charge Regulator MPPT Solar charge controller for 12V and 24V batteries Ultra fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency Efficient passive cooling without fans. Maximum efficiency over 98%. Utilize maximum charging current up to +40°C (104°F). Internal temperature sensor adjusts constant and charge retention voltages depending on temperature. Flexible charging algorithms Fully programmable charging algorithm (refer to software information), plus eight pre-programmed algorithms selectable via a rotary knob (refer to our manual for more details). Real-time monitoring with accessories Monitoring can be done with the appropriate accessories, either with a "ColorControl panel" or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding operating instructions.

BlueSolar Charge Regulator MPPT Solar charge controller for 12V and 24V batteries Ultra fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT regulator improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see Battery Life. The load output is short-circuit proof. Some loads (especially inverters) are best connected directly to the battery. Inverter remote control is best connected to the load output. A special interface cable may be required, please refer to the manual. Battery Life: intelligent battery management If the solar charge regulator is not able to charge the battery to its full capacity within a day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the battery's state of charge and if necessary, day after day, raises the load disconnect threshold (i.e., disconnects the load sooner) until the energy gained is sufficient to charge the battery to near 100%. From this point, the threshold for disconnecting the load is modulated so that charging to near 100% is achieved approximately once a week. Monitoring and control The charge regulator also features a programmable battery charging algorithm and a day/night time control with light dimming option. Monitoring can be done with the appropriate accessories either with a remote control or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding instruction manuals.

BlueSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves the energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a predefined voltage value. Alternatively, an intelligent battery management algorithm can be selected: see Battery Life. The load output is short-circuit proof. Some loads (especially inverters) connect best directly to the battery. Inverter remote control connectes best to the load output. A special interface cable may be required, please refer to the manual. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the status of the battery will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the battery's state of charge and if necessary, day after day, raises the load disconnect threshold (i.e., disconnects the load sooner) until the energy gained is sufficient to charge the battery to near 100%. From this point, the threshold for disconnecting the load is modulated so that charging to nearly 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The charge controller also has a programmable battery charging algorithm and day/night time control with light dimming option. Monitoring can be done with the appropriate accessories either with a remote control or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding instruction manuals.

Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). PowerControl work with limited generator power, limited shore or mains power The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist "power boost" of generators and shore power support (800VA/1200VA/1600VA only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries. High switch-on power This is required for switching on loads with high inrush currents such as voltage converters for LED lamps, halogen lamps or power tools. Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the multi will turn off at zero load or when only a light load is present and turn back on for a short period every two seconds. If the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again. Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low).

MultiPlusInverter / Charger Versatile use The MultiPlus is a high performance pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology and a high speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect from overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation

MultiPlusInverter / Charger Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). PowerControl work with limited generator power, limited shore or mains power The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist "power boost" of generators and shore power support (800VA/1200VA/1600VA only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries. High switch-on power This is required for switching on loads with high inrush currents such as voltage converters for LED lamps, halogen lamps or power tools. Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the Multi will turn off at zero load or when only a light load is present and turn back on for a short period every two seconds. If the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again. Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low).

MultiPlusInverter / Charger   Versatile use The MultiPlus Compact 12/1600/70-16 is a high performance pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology, and a high speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect against overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation.

MultiPlusInverter / Charger   Multifunctional use The MultiPlus Compact 12/2000/80-30 is a high performance pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology, and a high speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect against overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation.

The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It has all the functions of the MultiPlus plus an option of an external current transformer to implement the PowerControl, as well as PowerAssist functions or to optimize self-consumption with external current sensing (max. 32 A). It also offers all the features of the MultiGrid with the built-in anti-islanding function and an ever-growing list of countries where it is approved for feeding. A MultiPlus, plus ESS (Energy Storage System) function The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It offers all the functions of the MultiPlus, plus an external current sensor option that extends the function of the PowerControl and PowerAssist to 32 amps. It also offers all the features of the MultiGrid with the built-in anti-islanding feature and an ever-growing list of countries where it is approved for power feeding. Remote monitoring and control You can monitor and control your MultiPlus-II and system(s) on-site (LAN) or remotely anywhere in the world via the Internet using the free VRM App and the free VRM Portal website. It can be accessed from a phone, tablet, laptop or PC running a wide variety of operating systems. There are countless control options: For example, with the required Color Control GX or Venus GX, you can adjust your MultiPlus-II or have a back-up generator start automatically.

The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It has all the functions of the MultiPlus plus an option of an external current transformer to implement the PowerControl, as well as PowerAssist functions or to optimize self-consumption with external current sensing (max. 32 A). It also offers all the features of the MultiGrid with the built-in anti-islanding function and an ever-growing list of countries where it is approved for feeding. A MultiPlus, plus ESS (Energy Storage System) function The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It offers all the functions of the MultiPlus, plus an external current sensor option that extends the function of the PowerControl and PowerAssist to 32 amps. It also offers all the features of the MultiGrid with the built-in anti-islanding feature and an ever-growing list of countries where it is approved for power feeding. Remote monitoring and control You can monitor and control your MultiPlus-II and system(s) on-site (LAN) or remotely anywhere in the world via the Internet using the free VRM App and the free VRM Portal website. It can be accessed from a phone, tablet, laptop or PC running a wide variety of operating systems. There are countless control options: For example, with the required Color Control GX or Venus GX, you can adjust your MultiPlus-II or have a back-up generator start automatically.

InverterPhoenix Inverter VE.Direct   VE.Direct communication port The VE.Direct port can be connected to the following devices: With a computer (VE.Direct to USB interface cable required). With Apple and Android smartphones, tablets, Macbooks or other devices (VE.Direct Blu etooth smart dongle required). Fully configurable: Thresholds to trigger and reset low battery alarms. Thresholds to turn off and restart at low battery voltage levels. Dynamic shutdown: load-dependent shutdown threshold value. Output voltage 210 - 245V Frequency 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor. Monitoring: Input and output voltage and current Alarm Proven reliability The full bypass additionally with a ring transformer topology has proven itself for years. The inverters are short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). High inrush power This is needed for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. ECO mode In ECO mode, the inverter switches to standby as soon as the load drops below a preset value. In standby mode, the inverter then switches on for a short period of time (adjustable default setting: every 2.5 seconds). If the load exceeds a preset threshold during this time, the inverter remains switched on. Remote on/off switching A remote on/off switch can be connected with a two-pin connector or between the positive terminal of the battery and the left contact of the two-pin connector. Load switching to other AC sources: The automatic load switch For smaller powers, we recommend the Filax automatic transfer switch. Computers and other sensitive electronic equipment can thus continue to operate practically without interruption, since the switching times are very short (less than 20ms).

InverterPhoenix Inverter Smart   Built-in Bluetooth function: fully configurable via a tablet or smartphone Low battery voltage alarm Low battery voltage shutdown and restart thresholds Dynamic shutdown: load-dependent shutdown threshold value Output voltage: 210 - 245V Frequency: 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor Alarm relay Monitoring: input and output voltage, load and alarms The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable required) to configure and monitor the same parameters. Proven reliability The full bypass in addition with a ring transformer topology has been proven for years.The inverters are short-circuit proof and protected from overheating (whether caused by overload or ambient temperature). High inrush power This is required for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. ECO mode In ECO mode, the inverter switches to standby as soon as the load drops below a preset value. In standby mode, the inverter then switches on for a short period every 2.5 seconds (adjustable). If the load exceeds the preset threshold during this time, the inverter remains on. Remote on/off switching A remote on/off switch or relay contact can be connected to the two-pin connector. Alternatively, the H (left) terminal of the two-pin connector can be connected to a battery positive terminal or the L (right) terminal of the two-pin connector can be connected to the battery negative terminal (or to the body of a vehicle, for example).

InverterPhoenix Inverter Smart   Built-in Bluetooth function: fully configurable via a tablet or smartphone Low battery voltage alarm Low battery voltage shutdown and restart thresholds Dynamic shutdown: load-dependent shutdown threshold value Output voltage: 210 - 245V Frequency: 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor Alarm relay Monitoring: input and output voltage, load and alarms The VE.Direct communication port can be connected to a computer (VE.Direct to USB interface cable required) to configure and monitor the same parameters. Proven reliability The full bypass in addition with a ring transformer topology has been proven for years.The inverters are short-circuit proof and protected from overheating (whether caused by overload or ambient temperature). High inrush power This is required for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. ECO mode In ECO mode, the inverter switches to standby as soon as the load drops below a preset value. In standby mode, the inverter then switches on for a short period every 2.5 seconds (adjustable). If the load exceeds the preset threshold during this time, the inverter remains on. Remote on/off switching A remote on/off switch or relay contact can be connected to the two-pin connector. Alternatively, the H (left) terminal of the two-pin connector can be connected to a battery positive terminal or the L (right) terminal of the two-pin connector can be connected to the battery negative terminal (or to the body of a vehicle, for example).

Built-in Bluetooth function: Fully configurable via a tablet or smartphone. Low battery voltage alarm Low battery voltage shutdown and restart thresholds Dynamic shutdown: load-dependent shutdown threshold value Output voltage: 210 - 245V Frequency: 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor Alarm relay Monitoring: input and output voltage, load and alarms VE.Direct communication port The VE.Direct port can be connected to a computer (VE.Direct to USB interface cable is required) to configure and monitor the same parameters Proven reliability The full bypass in addition with a ring transformer topology has been proven for years.The inverters are short-circuit proof and protected from overheating (whether caused by overload or ambient temperature). High inrush power This is required for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. ECO mode In ECO mode, the inverter switches to standby as soon as the load drops below a preset value. In standby mode, the inverter then switches on for a short period every 2.5 seconds (adjustable). If the load exceeds the preset threshold during this time, the inverter remains on. Remote on/off switching A remote on/off switch or relay contact can be connected to the two-pin connector. Alternatively, the H (left) terminal of the two-pin connector can be connected to a battery positive terminal or the L (right) terminal of the two-pin connector can be connected to the battery negative terminal (or to the body of a vehicle, for example).

InverterPhoenix Inverter VE.Direct   VE.Direct communication port The VE.Direct port can be connected to the following devices: With a computer (VE.Direct to USB interface cable required). With Apple and Android smartphones, tablets, Macbooks or other devices (VE.Direct Blu etooth smart dongle required). Fully configurable: Thresholds to trigger and reset low battery alarms. Thresholds to turn off and restart at low battery voltage levels. Dynamic shutdown: load-dependent shutdown threshold value. Output voltage 210 - 245V Frequency 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor. Monitoring: Input and output voltage and current Alarm Proven reliability The full bypass additionally with a ring transformer topology has proven itself for years. The inverters are short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). High inrush power This is needed for switching on loads such as voltage converters for LED lamps, halogen lamps or power tools. ECO mode In ECO mode, the inverter switches to standby as soon as the load drops below a preset value. In standby mode, the inverter then switches on for a short period of time (adjustable default setting: every 2.5 seconds). If the load exceeds a preset threshold during this time, the inverter remains switched on. Remote on/off switching A remote on/off switch can be connected with a two-pin connector or between the positive terminal of the battery and the left contact of the two-pin connector. Load switching to other AC sources: The automatic load switch For smaller powers, we recommend the Filax automatic transfer switch. Computers and other sensitive electronic equipment can thus continue to operate practically without interruption, since the switching times are very short (less than 20ms).

SmartSolar Charge Regulator MPPT   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.

SmartSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency One cooling fan. Maximum efficiency at over 98 Flexible charging algorithms Fully programmable charging algorithm (also refer to the software page on our website) and eight pre-programmed algorithms that can be selected via a rotary knob (see our manual for more details). Comprehensive electronic protection Overheating protection and load reduction at high temperatures. PV short circuit and PV reverse polarity protection. PV reverse current protection.

SmartSolar Charge Regulator MPPT   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.

SmartSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% in comparison to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.

The 1,8m VE.Direct Cable from Victron (ASS030530203) is needed to connect devices that should communicate with each other via the VE-Direct port. For example, the BlueSolar controllers and the MPPT Control remote control panel. So the following connections can be made with it: Victron BlueSolar MPPT controller to Victron Color Control GX panel. Victron BlueSolar MPPT controller to MPPT Control remote panelBMV70xxx series to Color Control GX Panel BMV60xxx series to Color Control GX Panel Phoenix Inverter 12V 24V 48V 250W-500W to Color Control GX Panel VE.Direct cables are not included with these device series and are available in lengths from 0.3 to 10m. Scope of delivery:1x Victron ASS030530203 01,8m VE.Direct Cable

With the VE.Direct to Bluetooth Smart Dongle you can display your BMV or MPPT information on iOS and Android devices. You will need the VictronConnect app for this. Receive information like battery status, solar module energy and other useful data displayed wirelessly. The dongle can read data from all products with VE.Direct port. These include, for example, BMV-70x series battery monitors, Phoenix inverters with VE.Direct port and MPT solar charge controllers.

Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). PowerControl work with limited generator power, limited shore or mains power The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist "power boost" of generators and shore power support (800VA/1200VA/1600VA only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries. High switch-on power This is required for switching on loads with high inrush currents such as voltage converters for LED lamps, halogen lamps or power tools. Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the multi will turn off at zero load or when only a light load is present and turn back on for a short period every two seconds. If the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again. Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low).