Technology

DC-DC Charger Orion-Tr Smart DC/DC charger, galv. insulated Suitable for Bluetooth SmartMonitoring, changing settings and updating the charger when new software functions become available can be done with any Bluetooth enabled smartphone, tablet or other device. Fully programmable Battery charging algorithm (configurable) or fixed output. Intelligent generator compatibility: engine run detection. Adaptive 3-stage charging algorithm: constant current -constant voltage -maintenance. For lead acid batteries, it is important to keep the recording time short during shallow discharges to avoid overcharging the battery. After a deep discharge, the constant voltage duration is automatically extended to ensure that the battery fully charges.For lithium batteries, the recording time is fixed, by default 2 hours.Alternatively, a fixed output voltage can be selected. Remote on/off A remote on/off switch or relay contact can be connected to the two-pin connector. Alternatively, the H (right) terminal of the two-pin plug can be connected to a battery positive terminal or the L (left) terminal of the two-pin plug can be connected to the battery negative terminal (or to the body of a vehicle, for example).All models are short-circuit proof and can be connected in parallel to increase output current. An unlimited number of units can be connected in parallel. Overtemperature protectionThe output current is reduced at high ambient temperatures. Protection class IP43 When the screw terminals on the device are installed facing downwards. Screw terminals No special tools are required for installation. Input fuse (not replaceable)  

Powerful battery charger from Victron for 24V batteries with wireless monitoring function. Ready for Bluetooth Smart The Blue Smart IP22 battery charger is the wireless solution for monitoring voltage and current, adjusting settings and updating the charger when new features are available.Simply download the app to your smartphone and connect to the battery charger via Bluetooth. High efficiency With up to 94% efficiency, these chargers generate up to four times less heat compared to the industry standard. Also, after the battery is fully charged, power consumption drops to less than 0.5 watts, which is about five to ten times better than the industry standard. Adaptive 6-stage charging algorithm: Test- Bulk - Absorption - Recondition - Float - Storgage.The Blue Smart charger is characterized by its microprocessor-controlled, adaptive battery management. Adaptive means that the charging process is automatically adapted to the type of battery usage. Storage mode: Less maintenance and aging when the battery is not in use:Storage mode is activated whenever there has been no discharge within 24 hours. The charge maintenance voltage is then lowered to 2.2V/cell (13.2V for a 12V battery) to minimize gas generation and thus prevent corrosion on the positive plates. Once a week, the voltage is increased to the level of the gassing voltage. This provides a type of equalization charge that prevents electrolyte stratification and sulfation, the two main causes of premature battery failure. Also charges lithium-ion (LiFePO4) batteries LiFePO4 batteries are charged using a charge retention voltage phase algorithm. The NIGHT and LOW settings When the charger is in NIGHT or LOW mode, the output current is reduced to a maximum of 25% of the rated output and the charger operates absolutely silently. The NIGHT mode ends automatically after 8 hours. The LOW mode can be terminated manually. Protection against overheating The output current is reduced when the temperature rises up to 50°C, but the Blue Smart charger does not fail.

The ET112 (for single-phase operation with max. 100 A) and the ET340 (for three-phase operation with max. 65 A) are energy meters usually used in energy storage systems.The EM24 is designed to monitor three-phase operating modes only. There is one EM24 meter model for RS485 connection and one that can be connected via Ethernet. All ET models are connectable via RS485. This is used to measure the power and energy of the entire application in the distribution box.It can also be used to measure the output of a PV inverter. The data is then displayed on the Color Control GX and VRM Portal.

Technical data: H07RN-F 3G2,5 CEE plug 3-pole / 230V / 16A CEE-coupling 3-pole / 230V 16A with hinged cover IP44 certified tested according to VDE 0285-525-2-21; IEC 60309

COOL ON WHEELS Your space is limited? The compact Dometic CoolMatic CD 20 refrigerated drawer ensures that you don't have to go without the convenience of an effective cooling unit. This 20-liter refrigerated drawer is ideal for tight spaces and offers more flexibility thanks to the separately mountable cooling unit. The thermostat temperature control and convenient access via easy pull-out, ball-bearing drawer make the unit particularly efficient in use. In addition, the secure locking system allows the refrigerator drawer to be unlocked and opened in a single motion. More features: Its compact design makes it a space saver Temperature control with continuously adjustable thermostat improves efficiency Refrigerated goods particularly easy to access thanks to pull-out, ball-bearing drawer User-friendly unlocking and opening in a single movement Temperature range +15 °C to 0 °C The refrigeration unit can be mounted separately and the location thus flexibly selected The stainless steel door is elegant and robust Dimensions Product depth 564 mm Product height 250 mm 16.1 kg Electrical Input voltage (DC) 12/24 V Rated input current (DC) 3A DC12V/1.5A DC24V A Rated input power (DC) 36 W Performance Refrigerant, type R134a Contains fluorinated greenhouse gases GWP 1430 Refrigerant quantity 35 g CO2 equivalent 0.05 t Climate class (EN62552) N  

WATTSTUNDE® Solar Holding Spoiler Set Motorhome mounting spoiler for solar modules made of solid ABS all-plastic   The WATTSTUNDE® solar module holders give you the opportunity to mount your modules safely, efficiently and elegantly on your vehicle roof. 2 spoilers in a set Length: 68cm suitable for many solar modules from 50-120 watts Easy to mount UV and ozone resistant Aerodynamic shape prevents driving noise Can be mounted with Sikaflex 252i or Betalink K1 adhesive Extremely weather resistant incl. stainless steel screws Manufacturer warranty 20 years With these aerodynamic brackets you can safely and easily mount your solar modules  even without previous knowledge. The brackets have drill holes on both sides of the support surfaces. The modules can be glued or screwed to the holding spoilers. When screwing the modules, they can be removed again without further ado if necessary. For bonding, we recommend the strong construction adhesive Sikaflex 252i or Betalink K1 for a strong adhesive result. We explicitly advise against using any sealants for bonding! The profiles ensure better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. An investment that pays off! Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the retaining spoilers! The WATTSTUNDE® holding spoiler systems and roof penetrations are different from many others due to their very high load-bearing capacity as well as the UV and weather-resistant surface sealing. The elegant appearance of the retaining spoiler in combination with the module creates a sophisticated image on your vehicle roof.

SmartSolar Charge Regulator MPPT   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.

Connecting cable for batteries - cable lugs M8

Technical data: CEE plug and CEE coupling 230V / 16A, 3-pole length 10m K35 cold flexible up to -35°C tested according to OVE E 8241-55, IEC 60309

The LIONTRON LiFePO4 Smart BMS 12.8V 150Ah under-seat battery is a premium 12V lead-acid replacement with all the advantages of lithium iron phosphate technology. This compact battery is designed for under-seat installation and provides stable voltage even under extreme loads. With over 3000 charging cycles at 90% depth of discharge and an integrated battery management system (BMS), it ensures maximum safety. The Bluetooth 4.0 monitoring allows real-time tracking of critical battery data via smartphone. Ideal for demanding 12V applications.

WATTSTUNDE® ABS Roof Duct One Input   For gluing to the vehicle roof with PG screw connection for a cable entry. The ABS roof duct is simply bonded to the vehicle roof with Betalink K1 or Sikaflex adhesive 252i. The PG glands can squeeze a maximum cable diameter of 12mm and a minimum cable diameter of 4mm. One cable input With PG gland Made of ABS plastic Aerodynamic shape prevents driving noise Black and inconspicuous Can be mounted with Sikaflex or Betalink K1 adhesive UV and weather resistant Holds cables with a diameter of 4mm - 12mm tightly Dimensions approx. L 13 x W 4.5 x H 4 cm The WATTSTUNDE® roof bushings promise top safety. They are both UV and weather resistant and absolutely waterproof (IP68 standard). The PG safety cable glands ensure flush and gap-free sheathing of the cables, so that the penetration of dirt and water can be ruled out. The roof bushings round off your motorhome mounting system consisting of retaining spoilers, mounting corners and connectors and enable a solid mounting of your solar island system on the vehicle roof and a safe introduction of the cables into the living space.

Victron Lynx Shunt VE.Can The Lynx Shunt VE.Can is an intelligent 1000 A shunt (shunt resistor) with a provision for a fuse. With the built-in battery monitor, the battery state of charge can be accurately monitored. Use a GX device (e.g. Cerbo GX) to read the information. Part of the Lynx modular distribution system.

Victron Energy VE.Direct Cable 3m - single angled 90 degrees

MPP solar controller for high quality motorhomes, caravans and boats. Votronic solar controllers of the series "MPP" (Maximum-Power-Point) with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller continuously and automatically determines the maximum power point (MPP) of the solar panels several times per second. It then transforms the excess voltage of the solar module to a higher charging current for the battery (realized by high frequency switching controller technology with high efficiency). This charging current gain ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers are fully automatic, maintenance free and offer the following functions: MPP charge current increase compared to conventional controllers by 10% to 30% (efficiency > 95%) due to the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable during the cooler seasons and, for example, during periods of high snow, low and diffuse lighting (hibernation). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and back-up charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of insufficient solar power e.g. dusk, night etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of loads. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides equalization charging of individual battery cells (lead and lith.), then automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated. On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Measurement output for EBL, possibly existing electric block in the living area of the vehicle: Allows the convenient use of a (solar) current display built into the electric block to check the solar system. Please make sure to check the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel in advance, as we cannot assume any warranty for this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): Causes automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus. Connection for battery temperature sensor (Art.-No. 2001): In case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided. LiFePO4 batteries: Battery protection at high and especially at low temperatures. Highly recommended when the battery temperature may drop below 0°C during operation. Plug-ready for connection of Votronic solar display units LCD-Solar Computer S for optimal control of the system.

With the new Dometic CFX3, your outdoor experiences are easily controllable. Never seen before. The CFX3 gives you the power to change your mind at any time and put your well-being first. On the road, off the beaten path, in the backcountry or simply in the backyard, your everyday or extraordinary adventures will be accompanied by unspoiled food, less waste and a sense of security, letting you enjoy the here and now all around. MAXIMUM EFFICIENCY AND CAPACITY The Dometic CFX3 can store incredible amounts of food and beverages thanks to its new interior layout. The CFX3 eliminates the perishable food storage compartment, giving you even more space for your favorite foods. Decide on the layout yourself thanks to the removable divider grid, and benefit from more even distribution of cool air thanks to the expanded evaporator now located in all interior walls of the box. ... AND MORE Generous capacity of 46 l ExoFrame construction is durable yet lightweight. It features edges with protective frames and aluminum alloy handles. Powerful VMSO3 compressor cooling technology cools efficiently between +20 °C and -22 °C Easy-to-read, high-resolution color display and soft-touch buttons provide seamless monitoring and control of cooling performance. The smartphone app for CFX3 enables temperature control via WLAN or Bluetooth and provides a detailed performance overview. Three-stage battery protection system with automatic shutdown to avoid draining the car battery, as well as power draw capability through dual battery systems. Active seals provide excellent sealing, keeping cool air inside and minimizing power consumption.

With the HUB you can connect up to 7 battery groups, each group consisting of a maximum of 8 E-Boxes-4850 or E-Boxes-48100 in parallel connection. The connections of the individual groups converge in the HUB, so that they can run from it as a central point collected in the direction you want.

GX Touch 70 - Panels and System Monitoring The GX Touch 70 is the display accessory for our Cerbo GX. The 7-inch touchscreen display provides an instant overview of your system and allows you to make adjustments on the fly. It connects easily to Cerbo GX with a cable, its super slim, waterproof design, top-mounting, and easy installation provide plenty of flexibility in creating a clear and clean dashboard. Easy to install GX Touch is optimized to more than meet the standards of professional installers. The screen simply bolts to the top of a dashboard, eliminating the need to create perfect cutouts like the ColorControl GX, and connects via just one cable, eliminating the need to run multiple cables to the dashboard. The GX Touch 70 is an ideal match for the Cerbo GX - the all-new communication center allows you to always have perfect control of your system and maximize performance from anywhere. Simply connect via our Victron Remote Management (VRM) portal or access it directly via GX Touch 70, an MFD or our VictronConnect app using Bluetooth capability. This latest addition to the GX range combines the best in connectivity, redefining smart power solutions in every way.

Pole adapter set M6 with several connection options for batteries with internal thread to normal pole.Contains one pole adapter each for the plus and minus internal thread.

Bike Block Pro 2 zum Fixieren der Fahrräder. Schnell und sicher durch Quick-Clip-System an der vorderen Halterung.

Machen Sie ihren eigenen Strom! Mit unserem ESS-Heimspeicher Komplett-Set können Sie ihre Solarenergie für zu Hause speichern lassen. Unkompliziert, schnell, einfach.Alles was Sie für den Einsatz benötigen ist im Lieferumfang enthalten. Im Set enthalten sind: 1x Victron Energy Multiplus II 48/3000/35-32 Wechselrichter • Das MultiPlus-II kombiniert die Funktionen des MultiPlus und des MultiGrid. Er verfügt über alle Funktionen des MultiPlus und zusätzlich über eine Option eines externen Stromtransformators, um die Funktionen PowerControl, sowie PowerAssist umzusetzen oder den Eigenverbrauch mit externer Stromerfassung (max. 32 A) zu optimieren. Er bietet außerdem auch sämtliche Funktionen des MultiGrid mit der eingebauten Anti-Islanding-Funktion und einer immer länger werdenden Liste mit Ländern, in denen er für die Einspeisung zugelassen ist. 1x Victron Energy Cerbo GX • Überwachen Sie sofort den Ladezustand der Batterie, den Stromverbrauch, die Energiegewinnung aus PV, Generator und Netz oder überprüfen Sie Tankfüllstände und Temperaturmessungen. Steuern Sie einfach die Strombegrenzung für die Landstromeinspeisung, den (automatischen) Start/Stopp-Generator(en) oder ändern Sie beliebige Einstellungen, um das System zu optimieren. Verfolgen Sie Warnmeldungen, führen Sie Diagnoseprüfungen durch und lösen Sie Probleme aus der Ferne. Der Cerbo GX verwandelt jede Herausforderung an die Leistung in ein müheloses Erlebnis. 1x Victron Energy Meter EM24 - 3 Phasen Sensor • Der EM24 RS485 von Victron Energy ist ein 3-phasiger Stromzähler mit max. 65A pro Phase und RS485-Verbindungsschnittstelle. Das Energiemessgerät wird in Systemen mit einem GX-Gerät verwendet. Für die Verkabelung von RS485 gibt es zwei Möglichkeiten. Zum Einen die direkte Verbindung entweder über die RS485-zu-USB-Schnittstelle mit 1,8m Kabellänge ode über das 5m lange Kabel (nicht im Lieferumfang enthalten). Die zweite Möglichkeit ist die drahtlose Verbindung Zigbee. 1x Pytes E-Box - 48100R • Die E-Box bietet Ihnen einen sicheren, gut gestalteten und leistungsstarken Standard-LFP-Akku. Das battery pack ist kompakt, einfach zu installieren, wartungsfrei und kann als Baustein eines Energiespeichersystems eingesetzt werden, indem es parallel montiert wird. Die E-Box bietet eine intelligente, konfigurierbare Notstromversorgung bei Stromausfällen und versorgt ihr zuhause Tag und Nacht mit Solarenergie. 1x Verbindungskabel positiv 1x Verbindungskabel negativ 1x Datenkabel • Das Kabel von Pytes kann zur Datenübertragung zwischen Batterie und Wechselrichter eingesetzt werden. Die Länge beträgt 3,5m. 1x Pytes R-Box • Die ECOX R-BOX ist eine hochmoderne Energiespeicherlösung für zuhause. Sie hat insgesamt eine nutzbare Energiekapazität von 10 kWh.

SmartSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries   Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency One cooling fan. Maximum efficiency at over 98 Flexible charging algorithms Fully programmable charging algorithm (also refer to the software page on our website) and eight pre-programmed algorithms that can be selected via a rotary knob (see our manual for more details). Comprehensive electronic protection Overheating protection and load reduction at high temperatures. PV short circuit and PV reverse polarity protection. PV reverse current protection.

Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverter is short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). PowerControl work with limited generator power, limited shore or mains power The Multi Control remote control panel can be used to set the maximum shore or generator current to be drawn. The MultiPlus then takes into account other connected AC consumers and uses only the current that is "left over" for charging. This prevents the generator or shore power connection from being overloaded. PowerAssist "power boost" of generators and shore power support (800VA/1200VA/1600VA only) Load peaks often only occur for a limited period of time. In such a case, the MultiPlus ensures that insufficient shore power or generator power is immediately compensated by energy from the battery. If the load is reduced, i.e. if consumers are switched off, the energy that is then sufficiently available again can be used to charge the batteries. High switch-on power This is required for switching on loads with high inrush currents such as voltage converters for LED lamps, halogen lamps or power tools. Search mode When the search mode is set to 'on', the power consumption of the inverter is reduced by approximately 70% during no-load operation. In this mode, when operating in inverter mode, the multi will turn off at zero load or when only a light load is present and turn back on for a short period every two seconds. If the output current exceeds a set limit, the inverter resumes operation. If this is not the case, the inverter switches off again. Programmable relay In the default setting, the multifunction relay acts as an alarm relay, i.e. it switches off the device in the event of faults (device becomes too hot, ripple voltage at the input too high, battery voltage too low).

Dank EG-Genehmigung darf der E-Satz auch ohne Eintrag in die Fahrzeugpapiere durch den TÜV europaweit genutzt werden - sicheres und komfortables Fahren mit Anhänger oder Fahrradträger.   Lieferumfang: 1 x Westfalia fahrzeugspezifischer 13-poliger Elektrosatz Elektrosatz 13-pol./fzg-spez. passend für: Fiat Ducato, Peugeot Boxer, Citroen Jumper (alle Kasten ab BJ 02/2011)Ducato 7 NICHT passend für Ducato 8     Weite Informationen zum E-SATZ Anschluss im Motorraum Kabelstrang ist erweiterbar für Dauerplusleitung Kabelstrang ist erweiterbar für Ladeleitung Freischaltung nicht erforderlich Gewicht: 1,8kg

EcoFlow SMART GENERATOR (Dual Fuel) Durch das alternative Betreiben des Smart Generators mit 2 unterschiedlichen Brennstoffen (Benzin oder Propangas) erhältst Du noch mehr Sicherheit und Flexibilität bei Deiner eigenen, netzunabhängigen Stromerzeugung. Darüber hinaus bietet Flüssiggas den Vorteil einer einfachen, langen und geruchsfreien Lagerung. Es hinterlässt zudem mit 10 % weniger Kohlenmonoxid - Ausstoß einen besseren Fußabdruck als Benzin. Eine smarte Lösung für sowohl schnelles und zuverlässiges Laden Deiner Powerstation als auch das Betreiben von Verbrauchern. Optimal kombinierbar mit Delta Max, Delta Pro und Power Kits von EcoFlow Speziell für das Laden der Powerstations Delta Max und Delta Pro sowie für die Power Kits ist ein Anschluss mit Gleichstromladung und moderner X-Stream-Ladetechnologie vorhanden. Damit ist sehr schnelles, 40 % effizienteres Laden möglich: Delta Max 100% in 1,8 Stunden, Delta Pro in 2,7 Stunden. Dank dieser Verknüpfung aus Kompatibilität und neuester Technologie sind Deine Akkus schneller geladen bei einem geringerem Kraftstoffverbrauch und weniger Emissionen. Über einen separaten 230 V AC Ausgang mit reinem Sinus kannst Du zusätzlich auch Deine Verbraucher anschließen. Eine App mit sehr vielen Möglichkeiten und Funktionen Voraussetzung ist eine WiFi oder Bluetooth Verbindung. Schalte Dich einfach über Dein Smartphone auf das Gerät und starte bzw. beende den Smart Generator oder programmiere die Start/Stop Automatik mit einer entsprechenden Zeit. Lege einen bestimmten Ladestand Deiner Powerstation fest und aktiviere den Smart Generator. Dieser schaltet sich automatisch ein, sobald der Ladestand erreicht ist und wieder aus, wenn die Powerstation voll geladen (100 %) ist. Daneben hast Du viele weitere Möglichkeiten der Steuerung und Überwachung in Echtzeit. Selbstverständlich ist auch ein übersichtlicher LCD Bildschirm mit Bedienfeld am Gerät vorhanden, an dem Du Daten und Informationen bequem ablesen kannst. Sicherheit geht vor Hohe technische Standards gewährleisten einen sicheren Betrieb des Smart Generators. Neben einem Kohlenmonoxid Detektor ist das Gerät mit einer Warnfunktion für Öl- und Kraftstoffstand, Temperatur (Überhitzung) und vor Überladung ausgestattet. Alle Funktionen (bis auf die Kraftstoffstand - Warnung) lösen im kritischen Bereich ein automatisches Ausschalten des Smart Generators aus. Zur Sicherheit wird trotzdem empfohlen, das Gerät nicht über längere Zeit unbeaufsichtigt laufen zu lassen. Aufgrund seiner Emissionen sollte der Smart Generator nur im Außenbereich, vor Regen und Feuchtigkeit geschützt, betrieben werden. Die Powerstation kann über ein mitgeliefertes Kabel (5 m) im Innenbereich angeschlossen werden. Hohe Flexibilität und Effizienz Ob für Dein Wohnmobil, Deinen Schrebergarten, die Gartenparty oder bei einem Notfall (Stromausfall): Der Smart Generator Dual Fuel arbeitet zuverlässig mit 2 alternativen Antriebsstoffen, enorm schneller und effizienter Ladeleistung und smarter App - Steuerung. Vollgetankt und mit 10 kg Propangas erreicht der Generator eine Laufzeit von ca. 16 Stunden, was einer Energiekapazität von etwa 20 kWh entspricht. Gut durchdachte Warnfunktionen schützen das Gerät und die angeschossene Powerstation durch rechtzeitiges automatisches Abschalten. Das umfangreiche Zubehör ist im Lieferumfang enthalten und ermöglicht ein schnelles und unkompliziertes Starten und Anschließen des Smart Generators. Technische Informationen EcoFlow SMART GENERATOR Dual Fuel Gas - Anschlussschlauch Zusätzliches Batterieanschlusskabel Inklusive Motor (integriert): Viertakt, luftgekühlt Hubraum: 79,7 ccm Kraftstoff: Benzin (bleifrei) oder LPG (Propangas) Start Funktion: elektrisch, Automatisch, per App, manuell Warnfunktionen: Kohlenmonoxid, Öl-/Kraftstoffstand, Überladen, Überhitzung, Kurzschluss Geräuschlevel (bei 7m Entfernung): 56-67 dB