Versatile use The MultiPlus is a powerful pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology, and a high-speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect against overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation.

Versatile use The MultiPlus is a powerful pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology and a high-speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect against overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation.

Versatile use The MultiPlus is a powerful pure sine wave inverter, an advanced battery charger utilizing adaptive charging technology and a high-speed AC transfer switch in a single compact package. Models are available for the range of 800 VA to 5000 VA per module. Unique PowerAssist function The MultiPlus prevents overloading of a limited AC source. First, it automatically reduces battery charging to protect against overload. Next, it boosts the output of a generator or shore power supply with energy from the battery. Uninterruptible Power Supply (UPS) function. In the event of a mains fault or an interruption to the shore power or on-board generator, the multi's inverter is automatically switched on and takes over the supply to the connected loads. The switchover occurs so quickly (in less than 20 milliseconds) that uninterrupted operation of computers and other electronic equipment is guaranteed. Virtually unlimited power through parallel connection Up to six Multis can be connected in parallel for high power requirements. Three-phase or split-phase operation is also possible. Please refer to our data sheets to find out which models are suitable for parallel, three-phase and split-phase operation.

Victron Phoenix Voltage Converter 200W High-quality sine wave inverter for a stable 230V supply for small consumers Victron's Phoenix 12/250 VE.Direct is a high-quality sine wave inverter ideal for powering small 230V consumers on board. The continuous output power is 200 watts, which is sufficient for micro consumers such as laptops, battery chargers, mini PCs and other devices with small power requirements. However, it is also ideal for high-sensitivity radio, receiver as well as medical equipment. Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverters are short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). VE.Direct communication port The VE.Direct port can be connected to the following devices: With a computer (VE.Direct to USB interface cable required). To Apple and Android smartphones, tablets, Macbooks or other devices (VE.Direct Bluetooth smart dongle required). Fully configurable: Thresholds to trigger and reset low battery alarms. Thresholds to turn off and restart at low battery voltage levels. Output voltage 210 - 245V Frequency 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor monitoring: Input and output voltage and current alarms Other features at a glance: Power 200 W Brand quality from the Netherlands Output voltage with mains quality (pure sine wave) Compromise and trouble-free operation of small consumers such as laptop or chargers or mini PCs. Compact, light, robust and reliable programmable via VE.Direct connection numerous information readable via VE.Direct connection

Victron Phoenix Voltage Converter 300W Pure Sine Wave High-quality sine wave inverter for a stable 230V supply for small consumers Victron's Phoenix 12/375 VE.Direct is a high-quality sine wave inverter ideal for powering small 230V consumers on board. The continuous output power is 300 watts, which is sufficient for micro consumers such as laptops, battery chargers, mini PCs and other devices with small power requirements. However, it is also ideal for high-sensitivity radio, receiver as well as medical equipment. Proven reliability The complete bridging additionally with a ring transformer topology has proven itself for years. The inverters are short-circuit proof and protected against overheating (whether caused by overload or ambient temperature). VE.Direct communication port The VE.Direct port can be connected to the following devices: With a computer (VE.Direct to USB interface cable required). To Apple and Android smartphones, tablets, Macbooks or other devices (VE.Direct Bluetooth smart dongle required). Fully configurable: Thresholds to trigger and reset low battery alarms. Thresholds to turn off and restart at low battery voltage levels. Output voltage 210 - 245V Frequency 50 Hz or 60 Hz Threshold for ECO mode on/off and ECO mode sensor monitoring: Input and output voltage and current alarms Other features at a glance: Power 300 W Brand quality from the Netherlands Output voltage with mains quality (pure sine wave) Compromise and trouble-free operation of small consumers such as laptop or chargers or mini PCs. Compact, light, robust and reliable programmable via VE.Direct connection numerous information readable via VE.Direct connection

Victron SmartSolar 450/100-Tr MPPT RS Ultra-fast MPPT tracking The MPPT RS SmartSolar is a 48 V solar charge controller with a PV input voltage of up to 450 VDC and output current of either 100 A or 200 A. It is used in grid-tied and off-grid solar applications where maximum battery charging power is required. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP. However, this may not be the optimal MPP. The innovative algorithm of the SmartSolar device will always maximise the energy yield by adjusting to the optimal MPP. Highlight: Real-time data display on your smartphone! Built-in Bluetooth Smart: No dongle necessary A Bluetooth-enabled smartphone can display a wide range of data live. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices. Unlike the BlueSolar controllers, the Bluetooth interface is already built in here, so no additional accessories need to be purchased. Intelligent battery management with the BatteryLife algorithm The BatteryLife algorithm monitors the battery's state of charge and slightly increases the threshold value for switching off the load every day until the constant voltage is reached. From this point, the load disconnection threshold is modulated so that the constant voltage is reached approximately once a week. The BatteryLife algorithm will increase the operating life of the battery compared to conventional battery algorithms that always alternate between "partially charged" and "fully charged" (as a result of low self-discharge). Display and Bluetooth The display reads the parameters of the battery and controller. The parameters can be accessed with a smartphone or other Bluetooth-enabled device. Bluetooth can also be used to set up the system and change settings with VictronConnect. Internal temperature sensor and optional external measurement of battery voltage, temperature and current via Bluetooth. With a Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt, battery voltage and temperature (and current, in the case of a BMV 712 or a SmartShunt) can be transmitted to one or more SmartSolar charge controllers. Recovery function for fully discharged batteries Will initiate charging even if the battery has been discharged to 0 volts. Will reconnect to a fully discharged lithium-ion battery with internal disconnect function. Synchronised parallel charging with VE.Can or Bluetooth Up to 25 devices can be synchronised with VE.Can and up to 10 devices with Bluetooth. VE.Can and VE.Direct connection For connection to a GX device for system monitoring, data logging and remote firmware updates. With VE.Can, up to 25 devices can be connected in parallel and their charge synchronised.

Victron SmartSolar 450/200-Tr MPPT RS Ultra-fast MPPT tracking The MPPT RS SmartSolar is a 48 V solar charge controller with a PV input voltage of up to 450 VDC and output current of either 100 A or 200 A. It is used in grid-tied and off-grid solar applications where maximum battery charging power is required. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to adjust to a local MPP. However, this may not be the optimal MPP. The innovative algorithm of the SmartSolar device will always maximise the energy yield by adjusting to the optimal MPP. Highlight: Real-time data display on your smartphone! Built-in Bluetooth Smart: No dongle necessary A Bluetooth-enabled smartphone can display a wide range of data live. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices. Unlike the BlueSolar controllers, the Bluetooth interface is already built in here, so no additional accessories need to be purchased. Intelligent battery management with the BatteryLife algorithm The BatteryLife algorithm monitors the battery's state of charge and slightly increases the threshold value for switching off the load every day until the constant voltage is reached. From this point, the load disconnection threshold is modulated so that the constant voltage is reached approximately once a week. The BatteryLife algorithm will increase the operating life of the battery compared to conventional battery algorithms that always alternate between "partially charged" and "fully charged" (as a result of low self-discharge). Display and Bluetooth The display reads the parameters of the battery and controller. The parameters can be accessed with a smartphone or other Bluetooth-enabled device. Bluetooth can also be used to set up the system and change settings with VictronConnect. Internal temperature sensor and optional external measurement of battery voltage, temperature and current via Bluetooth. With a Smart Battery Sense, a BMV-712 Smart Battery Monitor or a SmartShunt, battery voltage and temperature (and current, in the case of a BMV 712 or a SmartShunt) can be transmitted to one or more SmartSolar charge controllers. Recovery function for fully discharged batteries Will initiate charging even if the battery has been discharged to 0 volts. Will reconnect to a fully discharged lithium-ion battery with internal disconnect function. Synchronised parallel charging with VE.Can or Bluetooth With VE.Can up to 25 devices can be synchronised, with Bluetooth up to 10devices. VE.Can and VE.Direct connection For connection to a GX unit for system monitoring, data logging and remote firmware updates. VE.Can can be used to connect up to 25 units in parallel and synchronise their charging.  

Victron MultiPlus 12/500/20-16 PMP121500000 230 V sine wave inverter and charger in one 12V charger with 20A charging current, also suitable for lithium batteries Sine wave inverter with 500VA (430W) Automatic transfer switch with 16A (switching time only 20ms) Dimensions 311x182x100 mm Weight: 4,4 kg The Victron MultiPlus 12/500 combines the function of an inverter, charger and transfer switch in one and that at a compact price.

Solar charge regulator MPP 350 Duo Digital MPPT solar charge controller with two charge outputs for automatic charging of the on-board and starter battery.   MPP solar regulator for high quality motorhomes, caravans and boats. Votronic "MPP" (Maximum-Power-Point) series solar controllers with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller continuously and automatically determines the maximum power point (MPP) of the solar panels several times per second. It then transforms the excess voltage of the solar module to a higher charging current for the battery (realized by high frequency switching controller technology with high efficiency). This charging current gain ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers are fully automatic, maintenance free and offer the following functions: MPP charge current increase compared to conventional controllers by 10% to 30% (efficiency > 95%) due to the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable during the cooler seasons and, for instance, during periods of high snow, low and diffuse lighting (hibernation). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and back-up charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of insufficient solar power e.g. dusk, night etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of loads. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides equalization charging of individual battery cells (lead and lith.), then automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated. On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Measurement output for EBL, possibly existing electric block in the living area of the vehicle: Allows the convenient use of a (solar) current display built into the electric block to check the solar system. Please make sure to check the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel in advance, as we cannot assume any warranty for this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): Causes automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus. Connection for battery temperature sensor (Art.-No. 2001): In case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided. LiFePO4 batteries: Battery protection at high and especially at low temperatures.Highly recommended when the battery temperature may drop below 0°C during operation. Plug-ready for connection of Votronic solar display units LCD-Solar Computer S for optimal control of the system.

Solar charge regulator MPP 165 Duo Digital MPPT solar charge controller with two charge outputs for automatic charging of the on-board and starter battery. MPP solar regulator for high quality motorhomes, caravans and boats. Votronic "MPP" (Maximum-Power-Point) series solar controllers with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller continuously and automatically determines the maximum power point (MPP) of the solar panels several times per second. It then transforms the excess voltage of the solar module to a higher charging current for the battery (realized by high frequency switching controller technology with high efficiency). This charging current gain ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers are fully automatic, maintenance free and offer the following functions: MPP charge current increase compared to conventional controllers by 10% to 30% (efficiency > 95%) due to the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable during the cooler seasons and, for example, during periods of high snow, low and diffuse lighting (hibernation). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and back-up charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of insufficient solar power e.g. dusk, night etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of loads. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides equalization charging of individual battery cells (lead and lith.), then automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated. On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Measuring output for EBL, possibly existing electric block in the living area of the vehicle: Enables the convenient use of a (solar) current display built into the electric block to check the solar system.Please be sure to check the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel in advance, as we cannot assume any warranty for this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): Causes automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus. Connection for battery temperature sensor (Art.-No. 2001): In case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided. LiFePO4 batteries: Battery protection at high and especially at low temperatures.Highly recommended when the battery temperature may drop below 0°C during operation. Plug-ready for connection of Votronic solar display units LCD-Solar Computer S for optimal control of the system.

Solar charge regulator SR 220 Duo Digital with two charge outputs for automatic charging of the on-board and starter battery.   Solar regulator for motorhomes, caravans and boats. The solar regulator is specially designed for use in motorhomes and caravans and is suitable for all lead-acid battery types and makes (acid, GEL/dryfit, AGM/fleece and LiFePO4 batteries). Through intelligent microprocessor control, the batteries are optimally charged with IU1oU2 characteristics. The solar controller works fully automatic and maintenance-free and offers the following functions: Charge output board battery I , depending on the battery type (lead or LiFePO4) optionally 3 or 5 charge programs. Charging output starter battery II: Separate secondary charging output with reduced charging current (12 V / 0.8 A or 1.5 A) for support charging and charge maintenance of the vehicle starter battery with protection against overcharging during long idle periods. The charging voltage is free of peaks and regulated to prevent overcharging of the batteries. Two battery charging outputs: automatic charging of the main or on-board battery (on-board I). Back-up charging as well as charge maintenance of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against battery back-discharge (in case of insufficient solar power e.g. dusk, night etc.), against overload and overheating. Buffer operation: Maintains charging characteristics even when operating simultaneously with loads on the battery. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: Defined charging voltage increase (U1) prevents harmful acid stratification and ensures equalization charging of the individual battery cells, then automatic trickle charging (U2). On-board filter: Built-in, allows easy parallel operation of the regulator with other charging sources, wind and gasoline generators, mains chargers, alternators, etc. on one battery. Connection for temperature sensor: Automatic adaptation of the charging voltage to the battery temperature. In cold weather, this results in a better full charge of the weaker battery; in summer temperatures, unnecessary battery gassing is avoided. Highly recommended if the battery is exposed to strong temperature fluctuations, e.g. in the engine compartment. Charging cable compensation: Voltage losses on the charging cables are automatically compensated. Measurement output for EBL (vehicle electrical block): Allows convenient use of the (solar) current display built into the electrical block to check the solar system. Please be sure to check the compatibility of your Schaudt electrical block (EBL) and the corresponding control and display panel in advance, as we cannot provide any warranty for this. Switching output "AES" (only SR 330-Duo Dig. and SR 530-Duo Dig.): Causes automatic switching of ELECTROLUX/DOMETIC refrigerators with "AES" (Automatic Energy Selector) from gas to 12 V operation in case of ample solar power surplus. Ready to plug in the Votronic solar display LCD-Solar Computer S for optimal control of the system. Charging programs 1 "Gel": Charging program for gel batteries, characteristic IU1oU2oU3 Adapted to sealed, gas-tight gel/dryfit batteries with fixed electrolyte which generally require a higher charging voltage level and longer U1 holding times, in order to achieve short charging times with particularly high capacity storage and to avoid long-term battery "starvation". 2 "AGM": Charging program for AGM/fleece batteries, characteristic IU1oU2oU3 Intended for charging sealed, gas-tight AGM (Absorbent-Glass-Mat) batteries in lead-fleece technology which require a particularly high U1 level with coordinated holding times for full charging and then a moderate U2 level for charge retention (plate and round cell technology). 4 "UNIVERSAL": Charging program for lead-acid/wet/AGM batteries, characteristic IU1oU2oU3 Universal program for charging and charge maintenance of acid batteries in vehicles (mixed mobile/stationary). With medium U1 level, still provides short charge times, good charge factor and good acid mixing for open and closed, low maintenance, maintenance free standard, traction, lighting, solar and heavy duty batteries, as well as AGM batteries with normal U1 level. Li "LiFePO4": Charging program for lithium batteries, characteristic IU1oU2oU3 Charging program adapted to lithium LiFePO4 batteries with own BMS and prescribed or built-in protection circuit. A special resting conservation automatically keeps the LiFePO4 battery at a charge level of 50-80% when the vehicle is parked (seasonal operation) which is beneficial for the service life and also buffers 12 V consumers and the vehicle starter battery. Note that the solar charge regulator should only be used with solar panels up to the maximum power rating (Wp) and below the maximum allowable voltage (Voc). Furthermore, the regulator is not suitable for an input-side connection (+/- solar panels) of wind, water, fuel or motor generators, power supplies, batteries or other power sources.

WATTSTUNDE® Holding Spoiler Connector Motorhome mounting bracket black for one or more solar modules made of solid ABS plastic.   With these solar connectors, larger solar modules can be fastened absolutely securely and easily. The connectors are suitable either to connect several modules together or to give large modules more stability. Solid holding pillar connectors universal fit UV resistant Weather resistant Made of solid solid plastic Aerodynamic shape prevents driving noise Easy to install with Sikaflex 252i or Betalink K1 adhesive incl. stainless steel screws Manufacturer warranty 20 years The retaining spoilers are bonded to the vehicle roof together with the module, either with Betalink K1 adhesive or Sikaflex 252i construction adhesive. The profiles provide better wind resistance while driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. WATTSTUNDE® solar mounts and fasteners differ from many others due to their very high load-bearing capacity and UV and weather-resistant surface sealing. Quality makes the difference, therefore Wattstunde® offers 20 years manufacturer warranty on the mounting spoilers!

WATTSTUNDE® Holding Spoiler Connector Motorhome mounting bracket white for one or more solar modules made of solid ABS plastic.   With these solar connectors, larger solar modules can be fastened absolutely securely and easily. The connectors are suitable either to connect several modules together or to give large modules more stability. Solid holding pillar connectors universal fit UV resistant Weather resistant Made of solid plastic Aerodynamic shape prevents driving noise Easy to install with Sikaflex 252i or Betalink K1 adhesive incl. stainless steel screws Manufacturer warranty 20 years The retaining spoilers are bonded to the vehicle roof together with the module, either with Betalink K1 adhesive or Sikaflex 252i construction adhesive. The profiles provide better wind resistance while driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module.WATTSTUNDE® solar mounts and fasteners differ from many others based on their very high load-bearing capacity and UV and weather-resistant surface sealing. Quality makes the difference, therefore Wattstunde® offers 20 years manufacturer warranty on the mounting spoilers!

WATTSTUNDE® Solar Holding Spoiler Set Motorhome mounting spoiler for solar modules made of solid ABS all-plastic The WATTSTUNDE® solar module holders give you the opportunity to mount your modules safely, efficiently and elegantly on your vehicle roof. 2 spoilers in a set Length: 53cm suitable for many solar modules from 50-120 watts Easy to mount UV and ozone resistant Aerodynamic shape prevents driving noise Can be mounted with Sikaflex 252i or Betalink K1 adhesive Extremely weather resistant incl. stainless steel screws Manufacturer warranty 20 years With these aerodynamic brackets you can mount safely and easily your solar modules even without previous knowledge. The brackets have drill holes on both sides of the support surfaces. The modules can be glued or screwed to the holding spoilers. When screwing the modules, they can be removed again without further ado if necessary. For bonding, we recommend the strong construction adhesive Sikaflex 252i or Betalink K1 for a strong adhesive result. We explicitly advise against using any sealants for bonding! The profiles ensure better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. An investment that pays off! Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the retaining spoilers! The WATTSTUNDE® holding spoiler systems and roof penetrations are different from many others due to their very high load-bearing capacity as well as the UV and weather-resistant surface sealing. The elegant appearance of the retaining spoiler in combination with the module creates a sophisticated image on your vehicle roof.

WATTSTUNDE® Solar Holding Spoiler Set Motorhome mounting spoiler for solar modules made of solid ABS all-plastic   The WATTSTUNDE® solar module holders give you the opportunity to mount your modules safely, efficiently and elegantly on your vehicle roof. 2 spoilers in a set Length: 53cm suitable for many solar modules from 50-120 watts Easy to mount UV and ozone resistant Aerodynamic shape prevents driving noise Can be mounted with Sikaflex 252i or Betalink K1 adhesive Extremely weather resistant incl. stainless steel screws Manufacturer warranty 20 years With these aerodynamic brackets you can mount your solar modules absolutely safe and easy even without previous knowledge. The brackets have drill holes on both sides of the support surfaces. The modules can be glued or screwed to the holding spoilers. When screwing the modules, they can be removed again without further ado if necessary. For bonding, we recommend the strong construction adhesive Sikaflex 252i or Betalink K1 for a strong adhesive result. We explicitly advise against using any sealants for bonding! The profiles ensure better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. An investment that pays off! Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the retaining spoilers! The WATTSTUNDE® holding spoiler systems and roof penetrations are different from many others due to their very high load-bearing capacity as well as the UV and weather-resistant surface sealing. The elegant appearance of the retaining spoiler in combination with the module creates a sophisticated image on your vehicle roof.

WATTSTUNDE® Solar Holding Spoiler Set   Motorhome mounting spoiler for solar modules made of solid ABS all-plastic The WATTSTUNDE® solar module holders give you the opportunity to mount your modules safely, efficiently and elegantly on your vehicle roof. 2 spoilers in a set Length: 68cm suitable for many solar modules from 50-120 watts Easy to mount UV and ozone resistant Aerodynamic shape prevents driving noise Can be mounted with Sikaflex 252i or Betalink K1 adhesive Extremely weather resistant incl. stainless steel screws Manufacturer warranty 20 years With these aerodynamic brackets you can mount your solar modules absolutely safe and easy even without previous knowledge. The brackets have drill holes on both sides of the support surfaces. The modules can be glued or screwed to the holding spoilers. When screwing the modules, they can be removed again without further ado if necessary. For bonding, we recommend the strong construction adhesive Sikaflex 252i or Betalink K1 for a strong adhesive result. We explicitly advise against using any sealants for bonding! The profiles ensure better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. An investment that pays off! Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the retaining spoilers! The WATTSTUNDE® holding spoiler systems and roof penetrations are different from many others due to their very high load-bearing capacity as well as the UV and weather-resistant surface sealing. The elegant appearance of the retaining spoiler in combination with the module creates a sophisticated image on your vehicle roof.

WATTSTUNDE® Solar Holding Spoiler Set Motorhome mounting spoiler for solar modules made of solid ABS all-plastic   The WATTSTUNDE® solar module holders give you the opportunity to mount your modules safely, efficiently and elegantly on your vehicle roof. 2 spoilers in a set Length: 68cm suitable for many solar modules from 50-120 watts Easy to mount UV and ozone resistant Aerodynamic shape prevents driving noise Can be mounted with Sikaflex 252i or Betalink K1 adhesive Extremely weather resistant incl. stainless steel screws Manufacturer warranty 20 years With these aerodynamic brackets you can safely and easily mount your solar modules  even without previous knowledge. The brackets have drill holes on both sides of the support surfaces. The modules can be glued or screwed to the holding spoilers. When screwing the modules, they can be removed again without further ado if necessary. For bonding, we recommend the strong construction adhesive Sikaflex 252i or Betalink K1 for a strong adhesive result. We explicitly advise against using any sealants for bonding! The profiles ensure better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimal rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. An investment that pays off! Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the retaining spoilers! The WATTSTUNDE® holding spoiler systems and roof penetrations are different from many others due to their very high load-bearing capacity as well as the UV and weather-resistant surface sealing. The elegant appearance of the retaining spoiler in combination with the module creates a sophisticated image on your vehicle roof.

WATTSTUNDE® Holding Spoiler Corners Motorhome mounting spoiler corners made of solid ABS solid plastic for mounting solar modules on the vehicle roof. Use these retaining spoiler corners as aerodynamic fasteners for small solar modules or as additional stabilization for larger modules to ensure optimum and secure hold on the roof of your motor home. Solid holding spoiler corners UV resistant Weather resistant Made of solid solid plastic Aerodynamic shape prevents driving noise Easy to install with Sikaflex 252i or Betalink K1 adhesive incl. stainless steel screws With these solar mounting corners (4 pcs.) solar modules can be mounted absolutely safe and easy. Before mounting and bonding the holding spoilers, the holding spoilers are screwed to the corners of the solar module. Then the profiles are bonded together with the module on the vehicle roof, either with Betalink K1 adhesive or Sikaflex 252i construction adhesive (available in the store). The profiles provide better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimum rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. WATTSTUNDE® solar mounts and fasteners stand out from many others due to their very high load-bearing capacity and UV and weather-resistant surface sealing. Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the mounting spoilers!

WATTSTUNDE® Holding Spoiler Corners Motorhome mounting spoiler corners made of solid ABS solid plastic for mounting solar modules on the vehicle roof. Use these retaining spoiler corners as aerodynamic fasteners for small solar modules or as additional stabilization for larger modules to ensure optimum and secure hold on the roof of your motor home. Solid holding spoiler corners UV resistant Weather resistant Made of solid plastic Aerodynamic shape prevents driving noise Easy to install with Sikaflex 252i or Betalink K1 adhesive incl. stainless steel screws With these solar mounting corners (4 pcs.) solar modules can be mounted absolutely safe and easy. Before mounting and bonding the holding spoilers, the holding spoilers are screwed to the corners of the solar module. Then the profiles are bonded together with the module on the vehicle roof, either with Betalink K1 adhesive or Sikaflex 252i construction adhesive (available in the store). The profiles provide better wind resistance when driving and, due to the distance between the solar module and the mounting surface, optimum rear ventilation of the module. Thus, compared to direct mounting, a significant increase in performance can be achieved by cooling the solar panel. WATTSTUNDE® solar mounts and fasteners stand out from many others due to their very high load-bearing capacity and UV and weather-resistant surface sealing. Quality makes the difference, which is why Wattstunde® offers a 20-year manufacturer's warranty on the mounting spoilers!

WATTSTUNDE® ABS Roof Duct One Input   For gluing to the vehicle roof with PG screw connection for a cable entry. The ABS roof duct is simply bonded to the vehicle roof with Betalink K1 or Sikaflex adhesive 252i. The PG glands can squeeze a maximum cable diameter of 12mm and a minimum cable diameter of 4mm. One cable input With PG gland Made of ABS plastic Aerodynamic shape prevents driving noise Black and inconspicuous Can be mounted with Sikaflex or Betalink K1 adhesive UV and weather resistant Holds cables with a diameter of 4mm - 12mm tightly Dimensions approx. L 13 x W 4.5 x H 4 cm The WATTSTUNDE® roof bushings promise top safety. They are both UV and weather resistant and absolutely waterproof (IP68 standard). The PG safety cable glands ensure flush and gap-free sheathing of the cables, so that the penetration of dirt and water can be ruled out. The roof bushings round off your motorhome mounting system consisting of retaining spoilers, mounting corners and connectors and enable a solid mounting of your solar island system on the vehicle roof and a safe introduction of the cables into the living space.

WATTSTUNDE® ABS Roof Duct One Input   For gluing to the vehicle roof with PG screw connection for a cable gland The ABS roof duct is simply bonded to the vehicle roof with Betalink K1 or Sikaflex adhesive 252i. The PG glands can squeeze a maximum cable diameter of 12mm and a minimum cable diameter of 4mm. One cable input With PG gland Made of ABS plastic Aerodynamic shape prevents driving noise Black and inconspicuous Can be mounted with Sikaflex or Betalink K1 adhesive UV and weather resistant Holds cables with a diameter of 4mm - 12mm tightly Dimensions approx. L 13 x W 4.5 x H 4 cm The WATTSTUNDE® roof ducts promise top safety. They are both UV and weather resistant and absolutely waterproof (IP68 standard). The PG safety cable glands ensure flush and gap-free sheathing of the cables, so that the penetration of dirt and water can be ruled out. The roof ducts round off your motorhome mounting system consisting of retaining spoilers, mounting corners and connectors and enable a solid mounting of your solar island system on the vehicle roof and a safe introduction of the cables into the living space.

WATTSTUNDE® ABS Roof Duct Two Entrances   For gluing to the vehicle roof with PG screw connection for cable input The ABS roof gland is simply glued to the vehicle roof with our Betalink K1 or Sikaflex adhesive 252i. The PG glands can squeeze a maximum cable diameter of 12mm and a minimum cable diameter of 4mm. Two cable inputs With PG gland Made of ABS plastic Aerodynamic shape prevents driving noise Can be mounted with Sikaflex or Betalink K1 adhesive UV and weather resistant Holds cables with a diameter of 4mm - 12mm tightly Dimensions approx. L 13 x W 9.5 x H 4 cm The WATTSTUNDE® roof ducts promise top safety. They are both UV and weather resistant and absolutely waterproof (IP68 standard). The PG safety cable glands ensure flush and gap-free sheathing of the cables, so that the penetration of dirt and water can be ruled out. The roof bushings round off your motorhome mounting system consisting of retaining spoilers, mounting corners and connectors and enable a solid mounting of your solar island system on the vehicle roof and a safe introduction of the cables into the living space.

WATTSTUNDE® ABS Roof Bushing Two Inputs   For gluing to the vehicle roof with PG screw connection for cable entry The ABS roof gland is simply glued to the vehicle roof with our Betalink K1 or Sikaflex adhesive 252i. The PG glands can squeeze a maximum cable diameter of 12mm and a minimum cable diameter of 4mm. Two cable inputs With PG gland Made of ABS plastic Aerodynamic shape prevents driving noise Can be mounted with Sikaflex or Betalink K1 adhesive UV and weather resistant Holds cables with a diameter of 4mm - 12mm tightly Dimensions approx. L 13 x W 9.5 x H 4 cm The WATTSTUNDE® roof bushings promise top safety. They are both UV and weather resistant and absolutely waterproof (IP68 standard). The PG safety cable glands ensure flush and gap-free sheathing of the cables, so that the penetration of dirt and water can be ruled out. The roof ducts round off your motorhome mounting system consisting of retaining spoilers, mounting corners and connectors and enable a solid mounting of your solar island system on the vehicle roof and a safe introduction of the cables into the living space.

WATTSTUNDE®SunFolder Solar Module   Generate solar energy simply and innovatively - with the new WATTSTUNDE® SunFolder solar bag, it's quick and easy. Unfold the bag, connect it and generate energy. Lightweight, innovative and flexible Because of its innovative design, the WATTSTUNDE® SunFolder 200Wp solar bag is very light, absolutely space-saving and offers an extremely high flexibility and usability. The solar bag scores with its ability to be freely aligned at any time. Whether behind the windshield when parked or simply outdoors. You can place the solar bag wherever the sun shines. It also gives you the guarantee of gaining a high energy yield from the SunPower Back-Contact solar cells. Because of the durable and water-repellent Cordura fabric, the bag can also be used in the rain.Practical feet allow you to place the solar panels at an angle so that the solar radiation can be used optimally. Plug & Play with practical plug-in system The SunFolder solar bag from WATTSTUNDE® has a 5m long connection cable, which is equipped with an Anderson plug-in system at the end. Thanks to the practical plug-in system, the connection plug can be permanently attached to the charge controller and if required, the solar bag can be taken out, hung or placed in the sun and you simply plug the two Anderson mating plugs together and the SunFolder is connected to the charge controller. It couldn't be faster or more convenient. Self-sufficient with SunPower solar cells The SunFolder solar pockets of the WATTSTUNDE® series are high-quality modules with SunPower cells that deliver optimal results and ensure a high energy yield. The solar pockets are suitable for all self-sufficient battery applications, such as motorhomes and campers, camping and tents, marine - sailboats, campervans, panel vans (including off-road vehicles such as Land Rover Defender) and in all OffGrid systems. Please note that no charge controller is included with the SunFolders. The reason for this is that in most cases charge controllers are already available or customers would like to choose a charge controller. Module type 12V module Nominal power (Pmpp) 200 Wp Max. Daily yield (summer) 1200 Wh/d Voltage (Umpp) 19.8 V Current (Impp) 10.10 A Open-circuit voltage (Uoc) 23.3 V Short-circuit current (Isc) 10.71 A bypass diode Integrated Cell efficiency >24 Dimensions (closed) 820 x 440 x 20 mm Dimensions (open) 820 x 1340 x 7.5 mm Connection cable 5 metres Weight 6.8 kg